Steel stock
Plate, sheet, beams, bars and hollow sections for fabrication and construction.
View sourceSteel and metals with material preparation and coordinated deliveries
Private to you. Nothing is shared with Tibnor A/S automatically.
Plate, sheet, beams, bars and hollow sections for fabrication and construction.
View source
Rebar, mesh and accessories are supplied with cutting, bending, rolling and welded reinforcement matched to construction drawings.
Network cutting, forming, sawing, coil processing and surface preparation supply material ready for the next fabrication step.
Price on request
Cut-to-length and mitre sawing. Danish brochure specifies 30° left/45° right; wider group angles are a separate processing route.
Price on request
Slit strip 0.28–6.0 mm thick, up to 1500 mm wide, tolerance ±0.30 mm through the network.
Price on request
Engineering steel cut to production lengths; network diameter 6–650 mm, with blade sawing limited to 180 mm.
Price on request
10–15 µm low-zinc silicate primer; thin plate/profile flatness and straightness limitations apply.
Price on request
Aluminium and other metals cut to length; a Taulov saw centre supports Danish supply.
Price on request
Network profile cutting of unalloyed and low-alloy steel in 6–300 mm thickness.
Price on request
Network plate cutting in 3–60 mm; workpiece-dependent ±2 mm tolerances under ISO 9013.
Price on request
Press braking to specified geometry through the Tibnor network; capacity up to 14 m and 4000 t depends on the processing unit.
Price on request
Tube and hollow-section cutting with washing, deburring and measuring through the network.
Price on request
Grey or red primers applied after shot blasting; formulation and layer thickness depend on the next fabrication/coating step.
Price on request
Steel shot cleaning to Sa 2.5. Width depends on line: source gives conflicting 2500/3000 mm limits; thin-material exceptions apply.
Price on request
Non-thermal cutting of steel, aluminium and other metals; network steel thickness up to 150 mm and aluminium 250 mm.
Sheet cut from coil 0.5–6.0 mm thick, up to 1500 mm wide, tolerance ±0.50 mm through the network.
Profiles to the SSAB manufacturing programme, including grades up to S900 and EN 10162.
Customer-specific quantities held for call-offs, with cut-to-size material and delivery/packing matched to production requirements.
Network laser cutting of plate up to 25 mm with ±0.2 mm tolerance; stainless format up to 2 × 4 m.
Material specialists support selection and source requirements outside the regular stock programme through supplier partners.
Rolled plate for shells and drums; network width 3250 mm and thickness 50 mm, with subcontracted thickness up to 120 mm.
Reinforcing bars 6–32 mm cut, bent or rolled to specified shapes.
Shapes and holes cut in beams, tubes and hollow sections through the processing network.
Deburring of smaller parts through the network; vibratory 300 kg batch/5 kg per part, tumble 500 kg batch/20 kg per part.
Project-specific welded reinforcement and secant-pile cages; custom mesh 6–32 mm, roll mesh 10–32 mm and one-way mesh up to 32 mm.
Triarca
Steel, copper and aluminium supply for Triarca distribution cabinets, fibre-network equipment and charging infrastructure, with technical dialogue and coordinated deliveries.
Hydrema
Hydrema consolidated steel purchasing with Tibnor in 2019, spanning plate, tubes and bars, with recurring material and production discussions.
CG Jensen
Roll mesh, reinforcing steel and bar reinforcement supplied for CG Jensen’s Rolighedsvej Bycampus construction in Frederiksberg, with NREP as developer. Work was underway in 2023, with the first phase then planned for 2024.
Haarup Maskinfabrik
Haarup used 2.5 tonnes of SSAB Zero plate in production trials described in 2024. Wider adoption remained planned; an earlier 420-tonne emissions reduction concerned other customer initiatives.
LJ Maskinteknik A/S
Supplied 500 tonnes of steel sawn to length and pallet-packed for LJ Maskinteknik’s robot-fed machining programme of 45,000 parts per year. LJ performed the machining; the delivery period is not stated.
ISO 9001:2015
DNV 288216-2019-AQ-DEN-DANAK; handling steel and metals at Prinsessens Kvarter 11, Fredericia. Valid 14 February 2024–13 February 2027.
ISO 45001:2018
DNV 288217-2019-AHSO-DEN-DANAK; handling steel and metals at Fredericia, also Danish Executive Order 1409 of 26 September 2020. Valid 14 February 2024–13 February 2027.
ISO 14001:2015
DNV C702621; Tibnor A/S Fredericia, handling steel and metals. Valid 21 January 2025–20 January 2028.
EN 1090-1:2009/A1:2011 EXC2
DNV 2388-CPR-24-91297 Rev 0.0, 26 June 2024; factory production control for structural steel components at Fredericia. Design excluded; no welding processes listed. Ongoing validity is conditional on unchanged scope and surveillance.
Ørsted renewable electricity certificate
Issued 9 December 2025 to Tibnor A/S for purchasing and cancelling European wind generation certificates matching actual consumption during 2026–2028. This is an electricity attribute arrangement. Expected matching volume: 3,901,514 kWh; actual consumption determines cancellation.
Tibnor A/S supplies steel, engineering steel, reinforcement, stainless steel, aluminium, copper, brass and other metals to Danish industry and construction. Plate, sheet, beams, bars, tubes and profiles are supported by material advice, customer-specific sourcing and stock call-offs. Processing includes sawing, cutting, forming and surface preparation through the Tibnor network. Danish services also cover cut and bent reinforcement, welded reinforcement and project-specific mesh. The Taulov sawing centre supplies cut-to-length material; Odense is the Danish business office. Larger processing capacities depend on the relevant Nordic facility and material. EDI and PunchOut connections support purchasing through customers’ own systems. Material certificates and product-specific environmental documentation support traceability and material selection. Danish customer work includes CG Jensen’s Frederiksberg campus reinforcement, prepared steel for LJ Maskinteknik and multi-metal supply for Triarca. EN 10204 3.1 documents accompany Taulov and Swedish central-stock material; 3.2 documents are available by agreement and additional charge through classification bodies. EDI supports EDIFACT/XML Monitor and customer-specific interfaces; PunchOut uses OCI.
Metal sheets
Claim this profile to review and manage its public information.
Tradebird created this profile from public sources. Tibnor A/S has not reviewed or endorsed it.
Updated Sep 13, 2026
